Effects of shear-induced crystallization on the complex viscosity of lamellar-structured concentrated surfactant solutions.

Material relationships at low temperatures were determined for concentrated surfactant solutions using a combination of rheological experiments, cross-polarized microscopy, calorimetry, and small angle X-ray scattering. A lamellar structured 70 wt% solution of sodium laureth sulfate in water was used as a model system. At cold temperatures (5 °C and 10 °C), the formation of surfactant crystals resulted in extremely high viscosity. The bulk flow behavior of multi-lamellar vesicles (20 °C) and focal conic defects (90 °C) in the lamellar phase was similar. Shear-induced crystallization at temperatures higher than the equilibrium crystallization temperature range resulted in an unusual complex viscosity peak. The effects of processing-relevant parameters including temperature, cooling time, and applied shear were investigated. Knowledge of key low-temperature structure-property-processing relationships for concentrated feedstocks is essential for the sustainable design and manufacturing of surfactant-based consumer products for applications such as cold-water laundry.

Dynamic diffusive interfacial transport (D-DIT): A novel quantitative swelling technique for developing binary phase diagrams of aqueous surfactant systems.

Current methods to develop surfactant phase diagrams are time-intensive and fail to capture the kinetics of phase evolution. Here, the design and performance of a quantitative swelling technique to study the dynamic phase behavior of surfactants are described. The instrument combines cross-polarized optical and short-wave infrared imaging to enable high-resolution, high-throughput, and in situ identification of phases and water compositions. Data across the entire composition spectrum for the dynamics and phase evolution of a binary aqueous non-ionic surfactant solution at two isotherms are presented. This instrument provides pathways to develop non-equilibrium phase diagrams of surfactant systems-critical to predicting the outcomes of formulation and processing. It can be applied to study time-dependent material relationships across a diverse range of materials and processes, including the dissolution of surfactant droplets and the drying of aqueous polymer films.

Characterizing Phase Transitions of Microfibrillated Cellulose Induced by Anionic and Cationic Surfactants.

Rheological modifiers are used to tune rheology or induce phase transitions of products. Microfibrillated cellulose (MFC), a renewable material, has the potential to be used for rheological modification. However, the lack of studies on the evolution in rheological properties and structure during its phase transitions has prevented MFC from being added to consumer, fabric, and home care products. In this work, we characterize surface-oxidized MFC (OMFC), a negatively charged colloidal rod suspension. We measure the rheological properties and structure of OMFC during sol-gel phase transitions induced by either anionic or cationic surfactant using multiple particle tracking microrheology (MPT). MPT tracks the Brownian motion of fluorescent probe particles embedded in a sample, which is related to the sample's rheological properties. Using MPT, we measure that OMFC gelation evolution is dependent on the charge of the surfactant that induces the phase transition. OMFC gelation is gradual in anionic surfactant. In cationic surfactant, gelation is rapid followed by length scale-dependent colloidal fiber rearrangement. Initial OMFC concentration is directly related to how tightly associated the network is at the phase transition, with an increase in concentration resulting in a more tightly associated network with smaller pores. Bulk rheology measures that OMFC forms a stiffer structure but yields at lower strains in cationic surfactant than in anionic surfactant. This study characterizes the role of surfactant in inducing phase transitions, which can be used as a guide for designing future products.

Gelation phase diagrams of colloidal rod systems measured over a large composition space.

Rheological modifiers tune product rheology with a small amount of material. To effectively use rheological modifiers, characterizing the rheology of the system at different compositions is crucial. Two colloidal rod system, hydrogenated castor oil and polyamide, are characterized in a formulation that includes a surfactant (linear alkylbenzene sulfonate) and a depletant (polyethylene oxide). We characterize both rod systems using multiple particle tracking microrheology (MPT) and bulk rheology and build phase diagrams over a large component composition space. In MPT, fluorescent particles are embedded in the sample and their Brownian motion is measured and related to rheological properties. From MPT, we determine that in both systems: (1) microstructure is not changed with increasing colloid concentration, (2) materials undergo a sol-gel transition as depletant concentration increases and (3) the microstructure changes but does not undergo a phase transition as surfactant concentration increases in the absence of depletant. When comparing MPT and bulk rheology results different trends are measured. Using bulk rheology we observe: (1) elasticity of both systems increase as colloid concentration increases and (2) the storage modulus does not change when PEO or LAS concentration is increased. The differences measured with MPT and bulk rheology are likely due to differences in sensitivity and measurement method. This work shows the utility of using both techniques together to fully characterize rheological properties over a large composition space. These gelation phase diagrams will provide a guide to determine the composition needed for desired rheological properties and eliminate trial-and-error experiments during product formulation.

Multiple particle tracking microrheology measured using bi-disperse probe diameters.

Multiple particle tracking microrheology (MPT) is a powerful tool for quantitatively characterizing rheological properties of soft matter. Traditionally, MPT uses a single particle size to characterize rheological properties. But in complex systems, MPT measurements with a single size particle can characterize distinct properties that are linked to the materials' length scale dependent structure. By varying the size of probes, MPT can measure the properties associated with different length scales within a material. We develop a technique to simultaneously track a bi-disperse population of probe particles. 0.5 and 2 µm particles are embedded in the same sample and these particle populations are tracked separately using a brightness-based squared radius of gyration, Rg2. Bi-disperse MPT is validated by measuring the viscosity of glycerol samples at varying concentrations. Bi-disperse MPT measurements agree well with literature values. This technique then characterizes a homogeneous poly(ethylene glycol)-acrylate:poly(ethylene glycol)-dithiol gelation. The critical relaxation exponent and critical gelation time are consistent and agree with previous measurements using a single particle. Finally, degradation of a heterogeneous hydrogenated castor oil colloidal gel is characterized. The two particle sizes measure a different value of the critical relaxation exponent, indicating that they are probing different structures. Analysis of material heterogeneity shows measured heterogeneity is dependent on probe size indicating that each particle is measuring rheological evolution of a length scale dependent structure. Overall, bi-disperse MPT increases the amount of information gained in a single measurement, enabling more complete characterization of complex systems that range from consumer care products to biological materials.

Combining Microfluidics and Microrheology to Determine Rheological Properties of Soft Matter during Repeated Phase Transitions.

The microstructure of soft matter directly impacts macroscopic rheological properties and can be changed by factors including colloidal rearrangement during previous phase changes and applied shear. To determine the extent of these changes, we have developed a microfluidic device that enables repeated phase transitions induced by exchange of the surrounding fluid and microrheological characterization while limiting shear on the sample. This technique is µ2rheology, the combination of microfluidics and microrheology. The microfluidic device is a two-layer design with symmetric inlet streams entering a sample chamber that traps the gel sample in place during fluid exchange. Suction can be applied far away from the sample chamber to pull fluids into the sample chamber. Material rheological properties are characterized using multiple particle tracking microrheology (MPT). In MPT, fluorescent probe particles are embedded into the material and the Brownian motion of the probes is recorded using video microscopy. The movement of the particles is tracked and the mean-squared displacement (MSD) is calculated. The MSD is related to macroscopic rheological properties, using the Generalized Stokes-Einstein Relation. The phase of the material is identified by comparison to the critical relaxation exponent, determined using time-cure superposition. Measurements of a fibrous colloidal gel illustrate the utility of the technique. This gel has a delicate structure that can be irreversibly changed when shear is applied. µ2rheology data shows that the material repeatedly equilibrates to the same rheological properties after each phase transition, indicating that phase transitions do not play a role in microstructural changes. To determine the role of shear, samples can be sheared prior to injection into our microfluidic device. µ2rheology is a widely applicable technique for the characterization of soft matter enabling the determination of rheological properties of delicate microstructures in a single sample during phase transitions in response to repeated changes in the surrounding environmental conditions.

Using µ2rheology to quantify rheological properties during repeated reversible phase transitions of soft matter.

A microfluidic device is designed to measure repeated phase transitions, gelation and degradation, on a single sample by exchanging the surrounding fluid while minimizing shear stress. This device enables quantitative microrheological characterization of material properties over multiple phase transitions, determining whether the material returns to the same equilibrium state. Fluid exchange is accomplished by using a two layer design, the sample is trapped in the first layer and the second layer is a well for the exchanging fluid. Fluid enters the sample chamber symmetrically creating equal pressure around the sample, trapping it in place. Multiple particle tracking (MPT) microrheology, a passive microrheological technique, measures the dynamic rheological properties during each phase transition. Combining rheological characterization and sample manipulation using microfluidics is termed µ2rheology. The utility of this technique is demonstrated by characterizing several phase transitions of a fibrous colloidal gel, hydrogenated castor oil. Gelation and degradation is induced by an osmotic pressure gradient created by contact with a glycerine based gelling agent and water, respectively. Several transitions are measured using a single sample. Nine transitions, five gel-sol and four sol-gel, are the maximum number of transitions characterized in a single sample. This microfluidic device and measurement technique is widely applicable and can be easily adapted to any system where solvent exchange is used to induce a change in material properties.

Quantifying the dynamic transition of hydrogenated castor oil gels measured via multiple particle tracking microrheology.

Rheological modifiers are essential ingredients in commercial materials that exploit facile and repeatable phase transitions. Although rheological modifiers are used to change flow behavior or quiescent stability, the complex properties of particulate gels during dilution is not well studied. We characterize a dynamically evolving colloidal gel, hydrogenated castor oil (HCO), a naturally sourced material, used in consumer products. This HCO scaffold consists of fibrous colloids, a surfactant (linear alkylbenzene sulfonate) and water. The gel undergoes critical transitions, degradation and formation, in response to an osmotic pressure gradient. Multiple particle tracking microrheology (MPT) measures the evolving material properties. In MPT, fluorescent probe particles are embedded into the sample and Brownian motion is measured. MPT data are analyzed using time-cure superposition, identifying critical transition times and critical relaxation exponents for degradation and formation where tc,deg = 102.5 min, ndeg = 0.77 ± 0.09, tc,for = 31.9 min, and nfor = 0.94 ± 0.11, respectively. During degradation and formation HCO gels evolve heterogeneously, this heterogeneity is characterized spatially and temporally. Heterogeneity of the gel is quantified by comparing variances of single particle van Hove correlation functions using an F-test with a 95% confidence interval. HCO transitions have rheological heterogeneous microenvironments that are homogeneously distributed throughout the field of view. Although HCO gels do evolve heterogeneously, this work determines that these heterogeneities do not significantly change traditional MPT measurements but the analysis techniques developed provide additional information on the unique heterogeneous scaffold microenvironments. This creates a toolbox that can be widely applied to other scaffolds during dynamic transitions.

Controlling the Mesostructure Formation within the Shell of Novel Cubic/Hexagonal Phase Cetyltrimethylammonium Bromide-Poly(acrylamide-acrylic acid) Capsules for pH Stimulated Release.

The self-assembly of ordered structures in mixtures of oppositely charged surfactant and polymer systems has been exploited in various cleaning and pharmaceutical applications and continue to attract much interest since their discovery in the late twentieth century. The ability to control the electrostatic and hydrophobic interactions that dictate the formation of liquid crystalline phases in these systems is advantageous in manipulation of structure and rendering them responsive to external stimuli. Nanostructured capsules comprised of the cationic surfactant, cetyltrimethylammonium bromide (CTAB), and the diblock copolymer poly(acrylamide-acrylic acid) (PAAm-AA) were prepared to assess their potential as pH responsive nanomaterials. Crossed-polarizing light microscopy (CPLM) and small-angle X-ray scattering (SAXS) identified coexisting Pm3n cubic and hexagonal phases at the surfactant-polymer interface. The hydrophobic and electrostatic interactions between the oppositely charged components were studied by varying temperature and solution pH, respectively, and were found to influence the liquid crystalline nanostructure formed. The lattice parameter of the mesophases and the fraction of cubic phase in the system decreased upon heating. Acidic conditions resulted in the loss of the highly ordered structures due to protonation of the carboxylic acid group, and subsequent reduction of attractive forces previously present between the oppositely charged molecules. The rate of release of the model hydrophilic drug, Rhodamine B (RhB), from nanostructured macro-sized capsules significantly increased when the pH of the solution was adjusted from pH 7 to pH 2. This allowed for immediate release of the compound of interest "on demand", opening new options for structured materials with increased functionality over typical layer-by-layer capsules.

Getting in shape: molten wax drop deformation and solidification at an immiscible liquid interface.

The controlled production of non-spherical shaped particles is important for many applications such as food processing, consumer goods, adsorbents, drug delivery, and optical sensing. In this paper, we investigated the deformation and simultaneous solidification of millimeter size molten wax drops as they impacted an immiscible liquid interface of higher density. By varying initial temperature and viscoelasticity of the molten drop, drop size, impact velocity, viscosity and temperature of the bath fluid, and the interfacial tension between the molten wax and bath fluid, spherical molten wax drops impinged on a cooling water bath and were arrested into non-spherical solidified particles in the form of ellipsoid, mushroom, disc, and flake-like shapes. We constructed cursory phase diagrams for the various particle shapes generated over a range of Weber, Capillary, Reynolds, and Stefan numbers, governed by the interfacial, inertial, viscous, and thermal effects. We solved a simplified heat transfer problem to estimate the time required to initiate the solidification at the interface of a spherical molten wax droplet and cooling aqueous bath after impact. By correlating this time with the molten wax drop deformation history captured from high speed imaging experiments, we elucidate the delicate balance of interfacial, inertial, viscous, and thermal forces that determine the final morphology of wax particles.

Formation of liquid-crystalline structures in the bile salt-chitosan system and triggered release from lamellar phase bile salt-chitosan capsules.

Nanostructured capsules comprised of the anionic bile salt, sodium taurodeoxycholate (STDC), and the biocompatible cationic polymer, chitosan, were prepared to assess their potential as novel tailored release nanomaterials. For comparison, a previously studied system, sodium dodecyl sulfate (SDS), and polydiallyldimethylammonium chloride (polyDADMAC) was also investigated. Crossed-polarizing light microscopy (CPLM) and small-angle X-ray scattering (SAXS) identified the presence of lamellar and hexagonal phase at the surfactant-polymer interface of the respective systems. The hydrophobic and electrostatic interactions between the oppositely charged components were studied by varying temperature and salt concentration, respectively, and were found to influence the liquid-crystalline nanostructure formed. The hexagonal phase persisted at high temperatures, however the lamellar phase structure was lost above ca. 45 °C. Both mesophases were found to dissociate upon addition of 4% NaCl solution. The rate of release of the model hydrophilic drug, Rhodamine B (RhB), from the lamellar phase significantly increased in response to changes in the solution conditions studied, suggesting that modulating the drug release from these bile salt-chitosan capsules is readily achieved. In contrast, release from the hexagonal phase capsules had no appreciable response to the stimuli applied. These findings provide a platform for these oppositely charged surfactant and polymer systems to function as stimuli-responsive or sustained-release drug delivery systems.

Two-dimensional Raman correlation spectroscopy study of an emulsion copolymerization reaction process.

The emulsion copolymerization of styrene and 1,3-butadiene using an oligomeric nonionic surfactant as an emulsifier to make a styrene-butadiene rubber (SBR) copolymer latex was monitored by real-time in situ Raman spectroscopy. Time-resolved Raman spectra collected during the early stage of the polymerization reaction were subjected to a series of data analysis techniques, including two-dimensional (2D) correlation spectroscopy, multivariate self-modeling curve resolution (SMCR), and kernel analysis, to elucidate the fine details of the complex reaction process. Generalized 2D correlation analysis of time-resolved Raman spectra readily identified the characteristic Raman scattering bands for the monomers and copolymer. Cross-peaks appearing in 2D Raman correlation spectra showed that the decrease in the spectral intensity of Raman bands assignable to 1,3-butadiene occurs before the band intensity changes for styrene or SBR copolymer. The positions of asynchronous cross-peaks were used to identify a spectral region with the most distinct pattern of intensity variations, which in turn could be used as the starting point for the alternating least squares iteration of the SMCR analysis. SMCR analysis of the time-resolved Raman spectra generated a set of estimated pure component spectra and concentration profiles of styrene, 1,3-butadiene, and SBR copolymer without requiring independently measured calibration data. The estimated concentration profiles of monomers and copolymer indicated that the reaction of 1,3-butadiene started before the consumption of styrene and production of SBR copolymer. Kernel analysis of the estimated concentration profiles provided a succinct measure of the similarity and dissimilarity of the concentration changes of monomers and copolymer.